How to Set Sata Hdd As Slave: Best Solution Ever

If you have an extra SATA hard drive sitting around, and you want to put it to use and want to know how to set SATA HDD as slave? A slave drive stores data but can’t be booted from. It’s easy to do and only takes a few minutes.

First, make sure that your motherboard supports SATA hard drives and that you have an available SATA port. If so, then power down your computer and unplug all of the cables from the back. Next, locate the empty SATA port on your motherboard and insert the hard drive into it.

Make sure that the connectors are properly aligned before screwing in the four screws that secure the hard drive to the chassis.


  • Power off your computer and unplug all power cords from the back of the tower
  • Open up the case by unscrewing the side panel screws and sliding off the panel
  • Find an empty bay to install your new hard drive into and remove the corresponding cover plate with a Phillips head screwdriver
  • Set your new HDD into the bay, using provided mounting screws to secure it into place if necessary, then replace and screw in the cover plate
  • Locate your old hard drive (now acting as a slave) and note its position in relation to other drives and devices in your computer for reference later
  • Using SATA cables, connect one end of each cable to their appropriate ports on each respective drive (master/slave), making sure not to cross-connect them by mistake
  • The connectors are keyed so they can only fit one way

Master/Slave Hard Drive Configuration

A master/slave hard drive configuration is a type of computer data storage arrangement where two or more hard drives are set up to work together. In this type of configuration, one hard drive is designated as the “master” while the other(s) are designated as “slaves.” The slave drives store copies of the data from the master drive, and they can be used to provide backup or redundancy in case the master drive fails. The main advantage of a master/slave configuration is that it can improve the performance of your computer’s storage system by distributing the workload between multiple drives. This can be especially beneficial if you have a lot of large files that need to be stored, such as video or audio files. When using a single drive to store these types of files, there can be noticeable delays when accessing them due to the amount of time it takes for the drive to seek out and read all of the data. However, with a master/slave configuration, each file can be spread out across multiple drives so that they can be accessed much more quickly.

Another advantage of this type of configuration is that it allows you to use lower-cost slave drives for storing data that isn’t accessed frequently. For example, you could use a small solid state drive (SSD) as your boot drive and then use one or more larger spinning hard drives (HDDs) as slaves for storing your media files. This would give you fast access to your operating system and applications while still providing plenty of storage space for all those videos and music tracks. If you’re thinking about setting up a master/slave hard drive configuration on your own computer, there are just a few things you need to keep in mind.

First, you’ll need to make sure that all of the drives you plan on using are compatible with each other. Second, you’ll need to choose whichdrive will serve as the master and which ones will be slaves – typically, smaller SSDs make good masters while larger HDDs make good slaves. Finally, pay attention to any software that might come with your hard drives; some manufacturers include special utilities designed specifically for setting up master/slave configurations (such as Intel’s Rapid Storage Technology).


How to Slave a Hard Drive Windows 10

If you’re running out of space on your primary hard drive, or if you want to back up your data in case of a drive failure, you can slave another hard drive. This process involves setting the new drive as a secondary storage device, and it can be done in Windows 10 with just a few clicks.

Here’s how:

  • First, make sure that the hard drive you’re using is properly formatted. In most cases, it will already be formatted for use with Windows, but if not, you can format it by right-clicking on the drive in File Explorer and selecting “Format.”
  • Once the drive is formatted, open Disk Management by searching for it in the Start Menu.
  • Right-click on the primary hard drive (usually labeled “C:”) and select “Properties.”
  • Under the “Volumes” tab, click on “Change Drive Letter and Paths.”
  • Click “Add,” then select “Mount in the following empty NTFS folder.”
  • Click Browse and choose an empty folder on your primary hard drive where you want to mount the new drive.
  • Give the new volume a label (like “D:”), then click OK to finish.
  • The new volume will now appear in File Explorer with its own letter assigned to it.

You can access it just like any other storage device on your computer. Keep in mind that any files stored on this drive will only be accessible when connected to this specific computer; if you try to access them from another PC, they’ll appear as corrupted data.

How to set SATA HDD as slave

Most modern computers come with two hard drive bays: one for a primary or system drive, and one for a secondary or slave drive. The drives are usually distinguished by their colored data cables–red for the primary (master) and black or blue for the secondary (slave). If you’re installing a new hard drive, you can designate it as either the primary or slave. If you’re adding a second drive to an existing computer, however, it must be configured as a slave. This is because most computers automatically configure any new hard drive as the primary.

Configuring a Hard Drive as Slave

  • Power down your computer and unplug all of the cables from the back except for the power cord
  • Open up your computer’s case using whichever method is appropriate for your model. This will give you access to the inside of your machine where the drives are located
  • Locate your current primary hard drive (the one that contains your operating system and all of your data). It should be connected to either Primary IDE Channel 0 or Primary IDE Channel 1 on the motherboard (channels are usually labeled clearly). Note which channel it’s connected to–you’ll need to connect your new drive to the same channel in order to make it slave correctly
  • If there is an empty slot next to your primary hard drive on its designated IDE channel, skip ahead to Step 7 Otherwise, continue with Step 5 if you wish to remove an unused optical or floppy drive in order to make room for your new hard disk (this isn’t necessary but may give you better airflow within the case)
  • Ground yourself before touching anything inside the case by touching a metal object such as the power supply unit; this will prevent static electricity from damaging sensitive components inside your computer while you’re working on it.. With one hand holding onto that object, use your other hand to gently remove any unused optical or floppy drives from their respective slots on either side of where you’ll be installingyour new hard disk..

You may needto unscrew some screws in order hold onto each device securely while removing it–be careful not touch any exposed circuitry on themodule itself when doing so.. Set these aside somewhere safe; we’ll put them back later once we’ve finished installing everything else..

How to Slave Ssd Drive

If you’re looking to get the most out of your SSD drive, then slaving it is a great way to do so. Slaving your SSD drive essentially means making it a secondary storage option on your computer – which can be extremely beneficial if used correctly. In this article, we’ll show you how to slave your SSD drive in just a few easy steps.

Before we begin, it’s important to note that slaving an SSD drive will only work if you have two drives installed on your computer – one being an SSD and the other being a regular hard drive. If you only have one drive installed, then unfortunately slaving isn’t an option.

With that said, let’s get started!

  • The first thing you’ll need to do is format your hard drive as NTFS. This can be done by right-clicking on the hard drive in My Computer and selecting “Format.”
  • Once that’s done, open up Disk Management (which can be found by searching for “disk mgmt.msc” in the Start Menu).
  • Right-click on the unallocated space on your hard drive and select “New Simple Volume.”
  • Follow the prompts until you get to the “Format Partition” screen – make sure that you format the partition as NTFS again.
  • Once that’s done, open up My Computer and right-click on your SSD drive.
  • Select “Properties,” then go to the “Security” tab and click on “Advanced.”
  • Under the “Owner” section, click on “Edit,” then select yourself as the owner of the file and check the box next to “Replace owner on subcontainers and objects.”
  • Click OK twice to close out of all of the windows.
  • Now go back into Disk Management and right-click on your SSD Drive.
  • Select “Change Drive Letter and Paths,” then click on “Add.”
  • Choose whatever letter you want for your SSD (we recommend using S:) and click OK twice to close out of all of Disk Management .
  • Right-clickon My Computer again and choose“Map Network Drive…” from the drop-down menu..Forthe “Drive”letter, enterin S: and for th e Folder, enterin \\localhost\S$. Click Finish to complete this process . Congratulations!

Hdd Master/Slave

The terms master and slave are used to describe the relationship between two devices. In general, the master is the device that controls the flow of information while the slave is the device that responds to commands from the master. When it comes to hard drives, the master/slave relationship can be a little bit confusing. The first thing you need to know is that there are two types of IDE hard drives: master and slave. A master drive is typically installed in the primary IDE controller on your motherboard, while a slave drive is installed in the secondary IDE controller. If you only have one hard drive, it will be automatically configured as a master drive.

Now, even though there are two types of IDE hard drives, there’s only one type of SATA hard drive: self-contained. This means that each SATA hard drive functions independently and does not require an additional cable for connectivity like IDE drives do. So, if you have multiple SATA hard drives installed in your system, there’s no need to worry about which one is acting as amaster or slave – they’re all just working together!

How Do I Make My Sata Hard Drive a Slave?

Assuming you would like to use the drive as an additional storage option and not as your primary OS drive, you can follow the steps below to make your SATA hard drive a slave. This will allow your computer to access and store data on the drive while still using another drive, typically an SSD, as your main Windows or operating system (OS) drive. Before getting started, it’s important to note that we recommend backing up any data you have stored on the SATA hard drive beforehand.

This is because making changes to how drives are set up in your computer (also called partitioning) can sometimes lead to data loss. With that said, let’s get started! The first thing you need to do is connect the SATA hard drive to your computer. If you’re unsure how to do this, consult your computer’s manual or the documentation that came with the SATA hard drive. Once it’s properly connected, power on both your computer and the SATA hard drive.

Next, open Disk Management, which is a built-in tool in Windows that lets users manage drives and partitions. To open Disk Management, type “partition” into the search bar next to the Start button and select “Create and format Hard Disk Partitions” from the results.

Alternatively, click on Start > Control Panel > System and Maintenance > Administrative Tools > Computer Management > Storage > Disk Management In Disk Management, locate the SATA hard drive you want to make a slave under “Disk Drives.” Right-click on it and select “Change Drive Letter And Paths…”. Click “Add…”, then “Assign The Following Drive Letter:”.
Choose a letter towards the end of the alphabet so that future drives won’t interfere with its assignment order (we usually go with “Y:”, but feel free to choose whatever letter you want).
After selecting a letter, click “OK” twice to close out of both windows. Your SATA hard disk should now appear under “This PC” with its newly assigned letter!

How Do I Make My Hard Drive a Slave Drive?

Assuming you would like to know how to make your hard drive a slave drive: A slave drive is a secondary storage device on a computer that is used to store data. A slave drive can be either an internal or external hard drive.
To make your hard drive a slave drive, you will need to change the jumper settings on the back of the hard drive. The Slave setting is typically denoted by an “S” on the jumper diagram. Once you have changed the jumper setting, you can then connect the hard drive to your computer using an available SATA or IDE port.

How Do I Change My Hard Drive from Master to Slave?

If you want to change your hard drive from master to slave, there are a few things you need to do. First, you’ll need to shut down your computer and unplug the power cord. Next, locate your hard drive and remove it from your computer. Once you have removed the hard drive, you’ll need to open it up and find the jumper settings.

The jumper settings will be different for each manufacturer, so consult your documentation or look online for more information. After you’ve found the correct jumper setting, change it from master to slave and then reattach the hard drive to your computer.
Once you’ve done that, plug in the power cord and boot up your computer. Your hard drive should now be recognized as a slave device.

Does Sata Have Master Slave?

Serial ATA (SATA) is a computer bus technology commonly used in desktop and laptop computers to connect hard drives and optical drives. SATA has replaced the older Parallel ATA (PATA) standard, which was designed for much slower speeds. One of the key features of SATA is that it uses point-to-point connections between devices, rather than a shared bus like PATA. This allows each device to have its own dedicated connection to the controller, which can improve performance. SATA does not have a master/slave relationship between devices like PATA did. Instead, each device is treated as an equal on the bus.
This can simplify things when connecting multiple devices, as there’s no need to worry about setting jumpers or anything like that.


If you want to set a SATA hard drive as a slave, there are a few things that you need to do. First, you need to make sure that the jumper setting on the back of the drive is set to “slave.” Next, you will need to connect the SATA cable from the motherboard to the drive.

Finally, you will need to connect a power cable from the power supply unit (PSU) to the drive. Once all of these connections are made, your SATA hard drive should be recognized by your computer as a slave device.

Stay With Gadgets Burner